Rinnai Error Code Priority light: Priority light on (this controller is in charge) (Tankless)

Updated October 15, 2026 · by Aurora Star Tech Inc.

Rinnai error code Priority light on a tankless water heater means: Priority light on (this controller is in charge). It is also called Rinnai diagnostic code Priority light.

Low severityTankless Water HeaterSENSEI RX/CX · SENSEI · KCM (RUCS/RUS)

Homeowner? What Rinnai code Priority light means for you

Usually minor Your tankless water heater is reporting: Priority light on (this controller is in charge). This code is usually informational or minor. The safe checks below often clear it; call us if it keeps showing up.

Safe things you can check yourself

Check that gas reaches the house: other gas appliances work, or the propane tank is not empty.
Make sure the heater is plugged in and its breaker is on. In winter, keep the power on: it protects the unit from freezing.
Outside, make sure the intake and exhaust pipes or vent cap are not blocked by snow, ice, leaves or a nest.
Check that the hot and cold water valves under the heater are fully open.
If you have a remote controller, turn it off and on once. If the code comes back, call a technician.

Call (647) 657-2977 Book a service call

Licensed technicians serving Vaughan, Toronto and the GTA.

What does Rinnai error code Priority light mean?

The orange Priority light glows on the controller that currently sets the temperature; the water heater is then ready to supply hot water. If it is off, press Priority on that controller. Priority can be moved only when no tap is open. On RX/CX units the Priority LED blinks during first power-up while SEt is displayed.

Applies to: Rinnai SENSEI, SENSEI RX/CX and KCM tankless with temperature controllers

Safety: Gas, electrical and refrigerant work must be done by a licensed technician. Turn off power and gas before servicing, never bypass a safety control, and always follow the manufacturer's manual for your exact model.

Rinnai models that use code Priority light

Show all 30 models

CU160e CU160i CU199e CU199i CX160i CX199i CXP160i CXP199i RSC160e RSC160i RSC199e RSC199i RU130e RU130i RU160e RU160i RU180e RU180i RU199e RU199i RUR160e RUR160i RUR199e RUR199i RX130i RX160i RX180i RX199i RXP160i RXP199i

Other Rinnai Tankless codes

Code	Meaning
ON	Hot water running (controller installed)
Out	Initial setting: outdoor installation
Parameter mode	Parameter settings menu
Parameter settings	Parameter (installer settings) mode
Perf data	Performance data viewer (live readings and counters)
Performance data	Performance data readout mode
rnS	Descaling finished, rinse now
S	Venturi reset sequence: step S (SENSEI)
SE	Cascade diagnostic display (error on secondary unit)
SEt	Initial settings not yet confirmed
SS	Service Soon alert (also listed as 55)
t	Venturi reset sequence: step t

All Rinnai Tankless Water Heater error codes →

Rinnai code Priority light: homeowner questions

What does Rinnai code Priority light mean?

Priority light on (this controller is in charge). The orange Priority light glows on the controller that currently sets the temperature; the water heater is then ready to supply hot water. If it is off, press Priority on that controller. Priority can be moved only when no tap is open. On…

Is it safe to keep using my tankless water heater with code Priority light?

Usually yes. Code Priority light is normally minor, but if it keeps coming back have it checked.

Can I reset Rinnai code Priority light myself?

You can try one reset (power off for 30 seconds, then on). If Rinnai code Priority light comes back, the cause is still there and a licensed technician should check it.

Who can fix Rinnai code Priority light near me?

Aurora Star Tech Inc. repairs Rinnai tankless water heaters in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.

Homeowner help: Tankless Water Heater No Hot Water: What to Check

Troubleshooting guides

No hot water All brands · Tankless Water Heater
Water temperature fluctuates All brands · Tankless Water Heater
Checking PC board fuses and thermistors Rinnai · Tankless Water Heater
Enter installer parameter mode (A button on the PC board) Rinnai · Tankless Water Heater
First power-up setup: gas type and indoor/outdoor (RX/CX) Rinnai · Tankless Water Heater
Lock or unlock the controller (key symbol) Rinnai · Tankless Water Heater
Lock or unlock the KCM controller (LOC) Rinnai · Tankless Water Heater
Performance data readout (items 01 to 24) Rinnai · Tankless Water Heater
Reset after cleaning the venturi or replacing the gas valve (codes 17 / 52) Rinnai · Tankless Water Heater
Reset the Service Soon (SS) reminder Rinnai · Tankless Water Heater
Show live flow and outlet temperature on the KCM controller Rinnai · Tankless Water Heater
Show the last 9 stored codes (diagnostic history) Rinnai · Tankless Water Heater
Start descaling (vinegar flush) mode on the PC board Rinnai · Tankless Water Heater
Switch the controller between Celsius and Fahrenheit Rinnai · Tankless Water Heater
Turn controller key beeps on or off Rinnai · Tankless Water Heater
Weak or missing flame signal (flame rod checks) Rinnai · Tankless Water Heater

Source: Rinnai N-Series Residential (100000467) / with Pump (100000508) / Commercial (100000504) / RSC SENSEI (100000773) Installation and Operation Manuals, 5.4 Setting the Temperature p.70; Rinnai SENSEI RX Residential Installation and Operation Manual (100000839), 5.4 p.57; Rinnai KCM Series Manual (U328-0700X04), p.54. Written in our own words as a summary; always check the original manual.

General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.