Navien Error Code System pressure: System pressure display (Boiler)

Updated October 16, 2026 · by Aurora Star Tech Inc.

Navien error code System pressure on a boiler means: System pressure display. It is also called Navien diagnostic code System pressure.

Low severityBoilerAlso Combi BoilerNavien NHB-H

Homeowner? What Navien code System pressure means for you

Usually minor Your boiler is reporting: System pressure display. This code is usually informational or minor. The safe checks below often clear it; call us if it keeps showing up.

Safe things you can check yourself

Check the thermostat: right mode (Heat or Cool), set a few degrees past room temperature, and fresh batteries if it uses them.
Make sure the unit has power: its on/off switch (often looks like a light switch near the unit) is ON and the breaker in the electrical panel is not tripped.
Look at the pressure gauge on the boiler. If it reads much lower than usual or near zero, or water is leaking, call a technician.
Outside, make sure the intake and exhaust pipes or vent cap are not blocked by snow, ice, leaves or a nest.
Check that the boiler gas valve is open (handle in line with the pipe).
Try one reset: turn the power off for 30 seconds, then back on. If the code comes back, stop resetting and call a technician.

Call (647) 657-2977 Book a service call

Licensed technicians serving Vaughan, Toronto and the GTA.

What does Navien error code System pressure mean?

Digits showing the internal water pressure of the boiler system.

Applies to: NHB-055H, NHB-080H, NHB-110H, NHB-150H

Safety: Gas, electrical and refrigerant work must be done by a licensed technician. Turn off power and gas before servicing, never bypass a safety control, and always follow the manufacturer's manual for your exact model.

Navien models that use code System pressure

NHB-055H NHB-080H NHB-110H NHB-150H

Other Navien Boiler codes

Code	Meaning
Supply Limit - No. of Times	EMS Data counter 9
Supply Temp	Status Information item 6 - Supply Temp
Sys Return Temp	Status Information item 9 - Sys Return Temp
Sys Supply Temp	Status Information item 8 - Sys Supply Temp
system/Zone3 Pump Status	Input/Output Status item 8 - system/Zone3 Pump Status
System check icon	System check or error needed
Tank Sensor Temp	Status Information item 13 - Tank Sensor Temp
Water Press	Status Information item 14 - Water Press
Zone2 Pump Status	Input/Output Status item 7 - Zone2 Pump Status
Zone V/V 1 Status	Input/Output Status item 9 - Zone V/V 1 Status
Zone V/V 2 Status	Input/Output Status item 10 - Zone V/V 2 Status
Zone V/V 3 Status	Input/Output Status item 11 - Zone V/V 3 Status

All Navien Boiler error codes →

Navien code System pressure: homeowner questions

What does Navien code System pressure mean?

System pressure display. Digits showing the internal water pressure of the boiler system.

Is it safe to keep using my boiler with code System pressure?

Usually yes. Code System pressure is normally minor, but if it keeps coming back have it checked.

Can I reset Navien code System pressure myself?

You can try one reset (power off for 30 seconds, then on). If Navien code System pressure comes back, the cause is still there and a licensed technician should check it.

Who can fix Navien code System pressure near me?

Aurora Star Tech Inc. repairs Navien boilers in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.

Homeowner help: Boiler Not Heating: What to Check

Troubleshooting guides

Condensing/corrosion of conventional boiler All brands · Boiler
No heat or some zones cold All brands · Boiler
Noise All brands · Boiler
Poor heat / circulation All brands · Boiler
Relief valve weeps every cycle / pressure climbs All brands · Boiler
Short cycling / wasted fuel All brands · Boiler
Symptoms of air in system All brands · Boiler
Uneven heating All brands · Boiler
Won't fire All brands · Boiler
Annual service checklist - Navien NHB-H Navien · Boiler
Change gas type with DIP switch 2 Navien · Boiler
Change installer parameters (password 1234) Navien · Boiler
Check input and output states (Input/Output Status) Navien · Boiler
Force a fixed firing rate with DIP switch 1 Navien · Boiler
Force minimum or maximum firing (special operations) Navien · Boiler
No space heat - Navien NHB-H / NFB-H Navien · Boiler
Open the service / installer menu (Back + Menu) Navien · Boiler
Purge air from the heating or DHW piping (Air Purge Mode) Navien · Boiler
Read live data (Status Information menu) Navien · Boiler
Read the error history Navien · Boiler
Relief valve discharging - Navien NHB-H / NFB-H Navien · Boiler
Remove a cascade (Cascade System Removal) Navien · Boiler
Reset one parameter to its default Navien · Boiler
Run test mode (fan, pumps, zone valves, venturi) Navien · Boiler
Set the altitude with DIP switch 2 Navien · Boiler
Set up a cascade (assign sub unit IDs) Navien · Boiler

Source: Navien NHB-H User's Information Manual (V1.0 Apr 2024), 2.3.1 Icons and Digital Display, p.7. Written in our own words as a summary; always check the original manual.

General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.