Fujitsu Error Code 22: Indoor unit capacity error (Heat Pump)
Fujitsu error code 22 on a heat pump means: Indoor unit capacity error. It is also called Fujitsu diagnostic code 22.
Homeowner? What Fujitsu code 22 means for you
Check, then call Your heat pump is reporting: Indoor unit capacity error. This is often caused by something simple. Try the safe checks below; if the code returns, book a service call before it turns into a no-heat or no-hot-water emergency.
Safe things you can check yourself
- Check the thermostat: right mode (Heat or Cool), set a few degrees past room temperature, and fresh batteries if it uses them.
- Check both breakers and the outdoor disconnect box beside the outdoor unit; all should be ON.
- Look at the air filter. If it is grey and clogged, replace it; a blocked filter causes many shutdowns.
- In winter, keep snow and ice off and away from the outdoor unit. A short defrost cycle with steam is normal.
- Try one reset: turn the power off for 30 seconds, then back on. If the code comes back, stop resetting and call a technician.
Call (647) 657-2977Book a service call
Licensed technicians serving Vaughan, Toronto and the GTA.
What does Fujitsu error code 22 mean?
Connected indoor capacity does not suit the outdoor unit (checked in the first 3 min after power-up). Indoor lamps: OPERATION (green) flashes 2x, TIMER (orange) flashes 2x, ECONOMY (green) flashes fast nonstop; wired remote shows 22.
Applies to: Fujitsu ductless heat pumps: Fujitsu ductless split/multi/VRF (general code list), Fujitsu wall-mounted 7-15 (NA ASU/AOU type), Fujitsu slim duct ARU 7-18 (LL type)
Common causes of Fujitsu code 22
- Wrong indoor sizes for this outdoor / multi combination
- Main PCB fault
Other Fujitsu Heat Pump codes
All Fujitsu Heat Pump error codes →
Fujitsu code 22: homeowner questions
What does Fujitsu code 22 mean?
Indoor unit capacity error. Connected indoor capacity does not suit the outdoor unit (checked in the first 3 min after power-up). Indoor lamps: OPERATION (green) flashes 2x, TIMER (orange) flashes 2x, ECONOMY (green) flashes fast nonstop; wired remote shows 22.
Is it safe to keep using my heat pump with code 22?
It depends on the cause. This is often caused by something simple. Try the safe checks below; if the code returns, book a service call before it turns into a no-heat or no-hot-water emergency.
Can I reset Fujitsu code 22 myself?
You can try one reset (power off for 30 seconds, then on). If Fujitsu code 22 comes back, the cause is still there and a licensed technician should check it.
Who can fix Fujitsu code 22 near me?
Aurora Star Tech Inc. repairs Fujitsu heat pumps in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.
Homeowner help: AC Running But Not Cooling: What to Check · Heat Pump Not Heating or Blowing Cold Air
Source: Fujitsu All Fujitsu split - multi - VRF (generic code list) codes.pdf - section error code table (indoor LED flashes); Fujitsu Wall-mounted 7-9-12-15 (North American trilingual, UTY-RNNUM remotes; e.g. ASU9-12-15 RLF1-RLS familie.pdf - section 14 Error codes; Fujitsu Wall-mounted KMCG (ASEH-AOEH 07-14) - Fujitsu UK; same error-code scheme as NA ASU-AOU units service S.pdf - section 3 Troubleshooting, 2 Troubleshooting with error code; Fujitsu Slim duct AR07-09-12-14-18 (ARU-ARYG LL-type equivalent) installation P-N 9381858064.pdf - section 14 Error codes. Written in our own words as a summary; always check the original manual.
General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.