Fujitsu Error Code 15: Check run unfinished / airflow auto-adjust error (Heat Pump)
Fujitsu error code 15 on a heat pump means: Check run unfinished / airflow auto-adjust error. It is also called Fujitsu diagnostic code 15.
Homeowner? What Fujitsu code 15 means for you
Usually minor Your heat pump is reporting: Check run unfinished / airflow auto-adjust error. This code is usually informational or minor. The safe checks below often clear it; call us if it keeps showing up.
Safe things you can check yourself
- Check the thermostat: right mode (Heat or Cool), set a few degrees past room temperature, and fresh batteries if it uses them.
- Check both breakers and the outdoor disconnect box beside the outdoor unit; all should be ON.
- Look at the air filter. If it is grey and clogged, replace it; a blocked filter causes many shutdowns.
- In winter, keep snow and ice off and away from the outdoor unit. A short defrost cycle with steam is normal.
- Try one reset: turn the power off for 30 seconds, then back on. If the code comes back, stop resetting and call a technician.
Call (647) 657-2977Book a service call
Licensed technicians serving Vaughan, Toronto and the GTA.
What does Fujitsu error code 15 mean?
The commissioning check run has not been completed (on ducted units this also covers a failed automatic airflow adjustment). Indoor lamps: OPERATION (green) flashes 1x, TIMER (orange) flashes 5x, ECONOMY (green) flashes fast nonstop; wired remote shows 15.
Applies to: Fujitsu ductless heat pumps: Fujitsu ductless split/multi/VRF (general code list), Fujitsu wall-mounted 7-15 (NA ASU/AOU type), Fujitsu slim duct ARU 7-18 (LL type)
Common causes of Fujitsu code 15
- Test run / check run not finished after install
- Duct static outside the unit range during auto adjust
Other Fujitsu Heat Pump codes
All Fujitsu Heat Pump error codes →
Fujitsu code 15: homeowner questions
What does Fujitsu code 15 mean?
Check run unfinished / airflow auto-adjust error. The commissioning check run has not been completed (on ducted units this also covers a failed automatic airflow adjustment). Indoor lamps: OPERATION (green) flashes 1x, TIMER (orange) flashes 5x, ECONOMY (green) flashes fast nonstop…
Is it safe to keep using my heat pump with code 15?
Usually yes. Code 15 is normally minor, but if it keeps coming back have it checked.
Can I reset Fujitsu code 15 myself?
You can try one reset (power off for 30 seconds, then on). If Fujitsu code 15 comes back, the cause is still there and a licensed technician should check it.
Who can fix Fujitsu code 15 near me?
Aurora Star Tech Inc. repairs Fujitsu heat pumps in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.
Homeowner help: AC Running But Not Cooling: What to Check · Heat Pump Not Heating or Blowing Cold Air
Source: Fujitsu All Fujitsu split - multi - VRF (generic code list) codes.pdf - section error code table (indoor LED flashes); Fujitsu Wall-mounted 7-9-12-15 (North American trilingual, UTY-RNNUM remotes; e.g. ASU9-12-15 RLF1-RLS familie.pdf - section 14 Error codes; Fujitsu Slim duct AR07-09-12-14-18 (ARU-ARYG LL-type equivalent) installation P-N 9381858064.pdf - section 14 Error codes. Written in our own words as a summary; always check the original manual.
General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.