Icon
Reliable Heating and Cooling Solutions – Quality Service, Fair Prices, Guaranteed Satisfaction!

Gree Error Code P4: Compressor drive PFC protection (Heat Pump)

Updated · by Aurora Star Tech Inc.

Gree error code P4 on a heat pump means: Compressor drive PFC protection. It is also called Gree diagnostic code P4.

High severityHeat PumpGree GMV6 Mini VRF

Homeowner? What Gree code P4 means for you

Call a technician Your heat pump is reporting: Compressor drive PFC protection. The heat pump has locked out or cannot run properly. One reset is fine; if the code comes back, it needs a licensed technician to find the cause.

Safe things you can check yourself

  • Check the thermostat: right mode (Heat or Cool), set a few degrees past room temperature, and fresh batteries if it uses them.
  • Check both breakers and the outdoor disconnect box beside the outdoor unit; all should be ON.
  • Look at the air filter. If it is grey and clogged, replace it; a blocked filter causes many shutdowns.
  • In winter, keep snow and ice off and away from the outdoor unit. A short defrost cycle with steam is normal.
  • Try one reset: turn the power off for 30 seconds, then back on. If the code comes back, stop resetting and call a technician.

Call (647) 657-2977Book a service call

Licensed technicians serving Vaughan, Toronto and the GTA.

What does Gree error code P4 mean?

Compressor drive fault: compressor drive pfc protection.

Applies to: Gree GMV6 Ultra Heat Mini VRF 36-60k (GMV-V..WL/C-T(U))

Common causes of Gree code P4

  • Compressor winding fault
  • Poor refrigerant flow or dirty coils/filters
  • Supply voltage problem

A technician checks these and 1 other possible causes on site before replacing any part.

Safety: Gas, electrical and refrigerant work must be done by a licensed technician. Turn off power and gas before servicing, never bypass a safety control, and always follow the manufacturer's manual for your exact model.

Gree models that use code P4

GMV-V36WL/C-T(U)GMV-V48WL/C-T(U)GMV-V60WL/C-T(U)

Other Gree Heat Pump codes

CodeMeaning
LCCompressor failed to start
LdCompressor phase loss
LJIndoor function DIP setting wrong
LPIndoor and outdoor units do not match
LUPG fan motor zero-crossing fault
oEUndefined outdoor unit error
P5Compressor phase overcurrent
P6Compressor drive IPM protection
P7Inverter module temperature sensor fault
P8Inverter module overheated
P9Inverter compressor lost synchronism
PACompressor drive memory chip fault

All Gree Heat Pump error codes →

Gree code P4: homeowner questions

What does Gree code P4 mean?

Compressor drive PFC protection. Compressor drive fault: compressor drive pfc protection.

Is it safe to keep using my heat pump with code P4?

It depends on the cause. The heat pump has locked out or cannot run properly. One reset is fine; if the code comes back, it needs a licensed technician to find the cause.

Can I reset Gree code P4 myself?

You can try one reset (power off for 30 seconds, then on). If Gree code P4 comes back, the cause is still there and a licensed technician should check it.

Who can fix Gree code P4 near me?

Aurora Star Tech Inc. repairs Gree heat pumps in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.

Homeowner help: AC Running But Not Cooling: What to Check · Heat Pump Not Heating or Blowing Cold Air

Troubleshooting guides

Source: Gree GMV6 Ultra Heat Mini VRF 36-60k (GMV-V36-48-60WL-C-T(U)) service.pdf - section Chapter 3 Faults, 4.1 Error Indication. Written in our own words as a summary; always check the original manual.

General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.

Emergency HVAC Service

647-657-2977