Icon
Reliable Heating and Cooling Solutions – Quality Service, Fair Prices, Guaranteed Satisfaction!

Gree Error Code C0: Communication fault IDU/ODU/wired controller (Heat Pump)

Updated · by Aurora Star Tech Inc.

Gree error code C0 on a heat pump means: Communication fault IDU/ODU/wired controller. It is also called Gree diagnostic code C0.

High severityHeat PumpGree GMV6 Mini VRF

Homeowner? What Gree code C0 means for you

Call a technician Your heat pump is reporting: Communication fault IDU/ODU/wired controller. The heat pump has locked out or cannot run properly. One reset is fine; if the code comes back, it needs a licensed technician to find the cause.

Safe things you can check yourself

  • Check the thermostat: right mode (Heat or Cool), set a few degrees past room temperature, and fresh batteries if it uses them.
  • Check both breakers and the outdoor disconnect box beside the outdoor unit; all should be ON.
  • Look at the air filter. If it is grey and clogged, replace it; a blocked filter causes many shutdowns.
  • In winter, keep snow and ice off and away from the outdoor unit. A short defrost cycle with steam is normal.
  • Try one reset: turn the power off for 30 seconds, then back on. If the code comes back, stop resetting and call a technician.

Call (647) 657-2977Book a service call

Licensed technicians serving Vaughan, Toronto and the GTA.

What does Gree error code C0 mean?

Indoor units, outdoor unit or the wired controller are not communicating.

Applies to: Gree GMV6 Ultra Heat Mini VRF 36-60k (GMV-V..WL/C-T(U))

Common causes of Gree code C0

  • D1/D2 wiring open, loose or mixed with H1/H2 or G1/G2
  • No power at an indoor unit
Safety: Gas, electrical and refrigerant work must be done by a licensed technician. Turn off power and gas before servicing, never bypass a safety control, and always follow the manufacturer's manual for your exact model.

Gree models that use code C0

GMV-V36WL/C-T(U)GMV-V48WL/C-T(U)GMV-V60WL/C-T(U)

Other Gree Heat Pump codes

CodeMeaning
b5Liquid line (valve) temperature sensor open or shorted
b6Accumulator inlet sensor open or shorted (20K)
b7Gas line (valve) temperature sensor open or shorted
bdSub-cooler gas inlet sensor open or shorted (20K)
bHSystem clock abnormal
bJHigh and low pressure sensors swapped
C1Main board to DC-DC controller communication fault
C2Main board to compressor drive communication fault
C3Main board to fan drive communication fault
C4Missing indoor units
C5Jumper (capacity) cap missing or bad
CHIndoor capacity too high

All Gree Heat Pump error codes →

Gree code C0: homeowner questions

What does Gree code C0 mean?

Communication fault IDU/ODU/wired controller. Indoor units, outdoor unit or the wired controller are not communicating.

Is it safe to keep using my heat pump with code C0?

It depends on the cause. The heat pump has locked out or cannot run properly. One reset is fine; if the code comes back, it needs a licensed technician to find the cause.

Can I reset Gree code C0 myself?

You can try one reset (power off for 30 seconds, then on). If Gree code C0 comes back, the cause is still there and a licensed technician should check it.

Who can fix Gree code C0 near me?

Aurora Star Tech Inc. repairs Gree heat pumps in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.

Homeowner help: AC Running But Not Cooling: What to Check · Heat Pump Not Heating or Blowing Cold Air

Troubleshooting guides

Source: Gree GMV6 Ultra Heat Mini VRF 36-60k (GMV-V36-48-60WL-C-T(U)) service.pdf - section Chapter 3 Faults, 4.1 Error Indication. Written in our own words as a summary; always check the original manual.

General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.

Emergency HVAC Service

647-657-2977