Lennox Error Code 3000: Replace filter 1 (Heat Pump)

Updated October 13, 2026 · by Aurora Star Tech Inc.

Lennox error code 3000 on a heat pump means: Replace filter 1. It is also called Lennox diagnostic code 3000.

Low severityHeat Pump

Homeowner? What Lennox code 3000 means for you

Usually minor Your heat pump is reporting: Replace filter 1. This code is usually informational or minor. The safe checks below often clear it; call us if it keeps showing up.

Safe things you can check yourself

Check the thermostat: right mode (Heat or Cool), set a few degrees past room temperature, and fresh batteries if it uses them.
Check both breakers and the outdoor disconnect box beside the outdoor unit; all should be ON.
Look at the air filter. If it is grey and clogged, replace it; a blocked filter causes many shutdowns.
In winter, keep snow and ice off and away from the outdoor unit. A short defrost cycle with steam is normal.
Try one reset: turn the power off for 30 seconds, then back on. If the code comes back, stop resetting and call a technician.

Call (647) 657-2977 Book a service call

Licensed technicians serving Vaughan, Toronto and the GTA.

What does Lennox error code 3000 mean?

Maintenance reminder from the S30/S40 thermostat (not a fault). S30/S40 thermostat alert code 3000.

Applies to: Lennox communicating heat pumps incl. variable-capacity inverter units in S30/S40 smart thermostat systems

Common causes of Lennox code 3000

Reminder interval reached

Safety: Gas, electrical and refrigerant work must be done by a licensed technician. Turn off power and gas before servicing, never bypass a safety control, and always follow the manufacturer's manual for your exact model.

Lennox models that use code 3000

EL16KP1-018 EL16KP1-024 EL16KP1-030 EL16KP1-036 EL16KP1-042 EL16KP1-048 EL16KP1-060 ML14KP1-018 ML14KP1-024 ML14KP1-030 ML14KP1-036 ML14KP1-042 ML14KP1-048 ML14KP1-060

Other Lennox Heat Pump codes

Code	Meaning
41	Device control board replaced
610	Low room temperature detected
611	High room temperature detected
700	Thermostat temperature sensor problem
701	Thermostat temperature above limit
703	Thermostat humidity sensor problem
3001	Replace filter 2
3002	Replace humidifier pad
3003	Replace UV bulb
3004	Maintenance reminder
3005	PureAir maintenance
65537	Missing base (smart hub)

All Lennox Heat Pump error codes →

Lennox code 3000: homeowner questions

What does Lennox code 3000 mean?

Replace filter 1. Maintenance reminder from the S30/S40 thermostat (not a fault). S30/S40 thermostat alert code 3000.

Is it safe to keep using my heat pump with code 3000?

Usually yes. Code 3000 is normally minor, but if it keeps coming back have it checked.

Can I reset Lennox code 3000 myself?

You can try one reset (power off for 30 seconds, then on). If Lennox code 3000 comes back, the cause is still there and a licensed technician should check it.

Who can fix Lennox code 3000 near me?

Aurora Star Tech Inc. repairs Lennox heat pumps in Vaughan, Toronto and across the GTA. Call (647) 657-2977 or book a service call online.

Homeowner help: AC Running But Not Cooling: What to Check · Heat Pump Not Heating or Blowing Cold Air

Troubleshooting guides

Heat pump not defrosting / outdoor coil iced - Lennox EL16KP1 / ML14KP1 Lennox · Heat Pump
Low capacity or abnormal pressures - Lennox EL16KP1 / ML14KP1 Lennox · Heat Pump
Outdoor unit will not start - Lennox EL16KP1 / ML14KP1 Lennox · Heat Pump
Two horizontal lines on display (soft disable) - Lennox communicating Lennox · Heat Pump

Source: Lennox Residential Communicating Systems Alert Code Guide (V2) 100017 (3/2023), Table 2 Alert Codes and Troubleshooting, p.47. Written in our own words as a summary; always check the original manual.

General guidance for qualified technicians. The manufacturer's installation and service manual and local codes always take priority. Aurora Star Tech is not affiliated with, endorsed by or sponsored by any equipment manufacturer; brand and model names are used only to identify equipment and belong to their owners.